Sizing brake discs correctly: comparison of grey cast iron, steel and stainless steel, thermal load, designs, minimum thickness and axial runout tolerance

AI This article was created with the help of AI.

ATEK Logo
ATEK Logo

Choice of material: grey cast iron, alloy steel and stainless steel compared

The choice of material determines the dimensional stability, wear behaviour and service life of a brake disc. The standard material is cast iron with flake graphite, for example EN-GJL-250: the lamellar graphite structure explains the high thermal conductivity of about 40 to 55 W/(m·K)[1] and gives the material pronounced damping properties and high compressive strength. Thermally, grey cast iron remains serviceable under load up to a surface temperature of around 600 °C; from about 700 °C it begins to glow[2]. This reliably covers the temperature profile of most industrial braking applications.

Alloy steels or stainless steel are used for corrosive environments. Important, and often mixed up in practice: heat resistance and corrosion resistance are two independent material properties. Stainless steel resists moisture, condensate and aggressive media much better, but conducts heat noticeably worse than grey cast iron and is more prone to distortion under high thermal load. Anyone sizing a disc for a wet, aggressive or hygiene-critical environment will find the relevant criteria for stainless steel brake discs in our technical article on this material.

MaterialThermal conductivityCorrosion behaviourTypical use
Grey cast iron (GJL, e.g. EN-GJL-250)40 to 55 W/(m·K)Rust film with moisture and idle periods, usually not criticalFriction rings up to around 600 °C surface temperature, standard for industrial disc brakes
Steel, unalloyed to alloyedapprox. 15 to 50 W/(m·K), depending on the alloydepending on the alloy, more corrosion-resistant than grey cast ironincreased corrosion requirements with moderate thermal load
Stainless steel (e.g. 1.4301)approx. 15 W/(m·K)[3]permanently corrosion-resistant, not resistant to intergranular corrosion in the welded condition[4]Marine, food and chemical environments with low to medium continuous thermal load

The property profile can also be controlled specifically within grey cast iron: the properties of grey cast iron can be improved by adding a wide variety of materials, such as chromium, molybdenum or carbon[5]. Very small additions such as chromium or molybdenum increase wear resistance and improve the heat-cracking behaviour of the microstructure[6]. The material specification is therefore not a detail but a sizing parameter: the material composition of the brake disc must be matched to the brake system, otherwise distortion and cracking behaviour suffer[5].

Formula for the thermal load during braking

Every braking operation converts kinetic energy into heat at the friction contact. The heat balance follows the relationship Q = m × c × ΔT (mass times specific heat capacity times temperature rise). For cast iron, c is about 0.46 kJ/(kg·K)[7]. As an example calculation: if a full braking operation introduces 405 kJ into a 5 kg disc, the formula gives a temperature rise of around 176 K. The disc therefore stores the energy primarily itself; whether the application works reliably depends on how quickly this heat is subsequently dissipated.

The surface temperature is the decisive limiting variable. Under heavy braking, lining and disc reach 500 to 550 °C, and a further rise in temperature is accompanied by a decrease in braking effect[8]. From about 650 °C the cast iron structure transforms into hard cementite, which results in uneven braking behaviour and cracking[8]. A generally valid target value for the maximum disc temperature is therefore 600 °C[2].

Solid, internally ventilated and two-piece designs compared

From this, the three relevant designs are derived. For industrial disc brakes, disc thicknesses between 12 and 50 mm, internally ventilated versions with diameters of 270 to 630 mm, and split, easily replaceable discs are available. We have summarised the selection criteria for industrial disc brakes in a guide of its own.

DesignHeat dissipationMoving massTypical use
Solid discHeat storage in the full mass, dissipation only via surface and hatfull disc mass, no savingStandard and holding brakes with low switching frequency, disc thicknesses 12 to 50 mm
Internally ventilated discradial cooling channels between the friction rings; the rotation creates a fan effect with a constant airflowlarger disc mass, but better heat dissipation than the solid discfrequent or long braking operations, high switching rate, diameter 270 to 630 mm
Two-piece designFriction ring made of grey cast iron, aluminium disc hat decouples the heat flow to the hubup to 20 % weight saving compared with the one-piece dischigh continuous thermal load, reduced unbalanced mass on fast shafts

With two-piece discs, thermal expansion must be included in the tolerance design: aluminium expands at around 23 × 10⁻⁶ K⁻¹, about twice as much as grey cast iron at 10 to 12 × 10⁻⁶ K⁻¹[1]. Fits and connection must compensate for this difference, otherwise stresses and axial runout deviations arise. For extreme ambient temperatures, for example at furnace doors, heat-resistant brakes with adapted materials are also used.

Assessing wear limit and minimum thickness correctly

The permissible minimum thickness is specified by the manufacturer and is usually stamped directly on the disc, mostly on the disc hat or at the edge, often with the marking MIN TH (minimum thickness)[9]. If the disc reaches or falls below it, it must be replaced: a disc that is too thin loses heat storage capacity and mechanical strength, and in extreme cases it cracks under thermal load. Measurement is taken with a micrometer in the area of the running surface swept by the lining, at several points distributed around the circumference, not across the wear ridge at the edge[9].

  • Heat cracks: result of cyclic thermal loading and of continued operation beyond the permissible temperature limit; the cracks change the disc geometry and runout
  • Thickness variation (DTV): uneven material transfer from the lining creates differences in thickness around the circumference; thickness variations of 0.012 to 0.015 mm should not be exceeded in order to avoid judder[10]
  • Cold judder caused by poor axial runout: as little as contamination of the hub seat with a few grains of sand produces 0.1 to 0.15 mm of axial runout at the outer radius[8]

Axial runout tolerance and its effect on braking performance

The axial runout, i.e. the side-to-side deviation of the mounted disc, not to be confused with radial runout, the deviation measured perpendicular to the axis of rotation, should be in the range of a few hundredths to a few tenths of a millimetre: with new discs the axial runout deviation should not exceed 0.070 mm, with older discs up to 0.10 mm is tolerable[10][12]. Larger deviations cause judder, uneven wear and vibrations throughout the drivetrain. How to maintain braking performance and smooth running through correct adjustment and maintenance is described in our guide to adjusting disc brakes.

  • Choosing the material solely by price instead of by the temperature and corrosion profile of the application: simple material specifications and changed tolerances lead to deformation and increased cracking[11]
  • Continued operation below the minimum thickness: the disc loses heat storage capacity and strength, and the risk of physical failure rises significantly[8]
  • Failure to take thermal expansion into account in the tolerance design of two-piece discs, especially with the pairing of grey cast iron friction ring and aluminium hat

Corrosion protection without loss of thermal performance

Surface rust on grey cast iron discs is caused by moisture and longer idle periods and is unavoidable, but usually not critical: the lining wears off the thin rust film during operation. It becomes critical when corrosion forms on contact surfaces, for example on the hub contour or on mating surfaces. There, rust jacking (rust build-up under the contact surfaces) causes specific damage patterns: axial runout deviation, brake judder and vibrations that only show up in operation[8]. The seating surfaces must therefore be kept clean and free of corrosion at every installation.

For permanently corrosive environments, from marine settings through food production to the pharmaceutical industry, stainless steel is the material alternative, albeit with the thermal disadvantages from the first section: lower thermal conductivity and therefore a greater tendency to distort under continuous load. The choice of material is thus always a trade-off between corrosion resistance and thermal performance, never a decision based on price alone.

  • Specify a precisely matched material pairing of friction material and disc: ATEX conformity is confirmed, for example, only for the combination of friction material 544 with the disc material EN-GJS-400-15
  • Choose the friction material according to the application profile: sintered metal compounds for high-temperature and high-speed applications, highly graphitised compounds, which counteract noise through their lubricating effect, for continuous-slip brakes
  • Use coating systems and surface protection that provide corrosion protection without impeding the heat dissipation of the friction ring
  • Embed maintenance firmly: clean contact surfaces, measure residual thickness and axial runout regularly, document wear

The system perspective is decisive: brake disc, friction material and brake form a coordinated overall system, and this system is in turn only one component of the complete drivetrain. At ATEK Drive Solutions, we therefore develop brakes, gearboxes and motors with controllers as one integrated, project-ready solution from a single source, matched to your temperature, corrosion and load profile. Which brake technology is right for which application is summarised in our overview of brake technology for industrial drives.

Frequently asked questions

Which material is right for a brake disc?

For most industrial applications, grey cast iron with flake graphite (e.g. EN-GJL-250) is the standard: good thermal conductivity, high compressive strength and pronounced damping. Alloy steels or stainless steel are used in corrosive or aggressive environments, but are more expensive and conduct heat less well, which leads to a stronger tendency to distort under high thermal load.

How is the thermal load of a brake disc calculated?

The heat generated during braking follows Q = m × c × ΔT, i.e. mass × specific heat capacity × temperature rise. For grey cast iron, c is 0.46 kJ/(kg·K); an example calculation from the literature gives a heating of around 176 K per full braking operation for a front car brake disc. The braking power supplied and the heat power dissipated are also decisive.

At what temperature does a brake disc lose performance?

The friction coefficient of iron alloys decreases significantly at high temperatures from about 500 °C. With repeated or long braking operations, the disc can be heated to red heat; thermal stresses then lead to permanent distortion and stress cracks.

What do internally ventilated and two-piece brake discs offer?

Internally ventilated discs have radial cooling openings between the friction surfaces; the centrifugal force of the rotary motion creates a constant airflow and improves heat dissipation. Two-piece discs combine an aluminium disc hat with a grey cast iron friction ring: aluminium conducts heat about four times better than steel and at the same time reduces the moving mass.

Why must a brake disc never fall below its minimum thickness?

The permissible minimum thickness is the wear limit specified by the manufacturer, usually stamped as MIN TH on the outer edge or disc hat. If it is reached or the disc falls below it, the fracture strength of the disc drops significantly and there is a risk of cracking and fracture, so the disc must be replaced.

What axial runout tolerance is usual for brake discs?

The axial runout should be in the range of a few hundredths to a few tenths of a millimetre. Larger deviations lead to thickness variation, cold judder, uneven wear and vibrations; typical causes are poor axial runout of the hub, unclean installation or rust jacking at the contact surfaces.

How can brake discs be protected against corrosion without weakening thermal performance?

Surface rust on grey cast iron caused by moisture and idle periods is usually not critical. Rust jacking at contact surfaces, which impairs axial runout and braking behaviour, is critical. In corrosive environments, stainless steel discs or suitable coating systems can be used, although the poorer thermal conductivity of stainless steel must be taken into account in the overall thermal balance.

Sources

  1. mk-strangguss.de
  2. hella.com
  3. metalcor.de
  4. m.woite-edelstahl.info
  5. hella.com
  6. at-rs.de
  7. schweizer-fn.de
  8. ferodo.com
  9. kfz-dietrich.com
  10. magazin-metamorphosen.de
  11. otto-zimmermann.de
  12. hella.com