Your Choice: Type VLM 090
Characteristics
Performance Data

Characteristic Standard Option
Toothing Bevel gear, spiral-toothed See chapter 6.2.1
Gear ratio 3:1 to 6:1
Housing / Flanges Grey cast iron
Threaded mounting hole On all housing surfaces without flange and on all flanges. See chapter 6.2.3
Shaft Material 1 C45, shaft ends greased

Fit with ISO 6 tolerance with parallel keyway: according to DIN 6885 Sheet 1

See chapter 4.6.2
Hollow shaft Material 1 C45, shafts greased

Fit with ISO 7 tolerance with parallel keyway: according to DIN 6885 Sheet 1

See chapter 4.6.3
Radial shaft seal ring NBR, form A See chapter 4.8
Ambient temperature - 10°C to +90°C. The values of the performance tables are valid for +20°C See chapter 4.9.3
Circumferential backlash < 30 arcmin See chapter 6.2.10
Protection class IP 54 See chapter 4.5
Corrosion protection Prime coat; layer thickness > 40 µm See chapter 4.4.1
Bearing life L10h more than 15,000h See chapter 4.9.1
Oil change intervals Not required if the oil temperature is kept < 90°C

The lifetime of the bearings can be increased by the factor 1.5 if the oil is changed after the first 500 service hours and then every 5000 service hours.

See chapter 6.2.8
Lubricants Synthetic lubricants See chapter 6.2.8
Motor IEC standard motor in the prescribed efficiency class

P1 [kW] n2  [rpm] T2 [Nm] T2N [Nm] T2MAX [Nm] i [-] IEC motor Gearbox size P1NT [kW]
0.18 335 4.9 27 70 4:1 063B-4 090 3.8
268 6.1 27 60 5:1 063B-4 090 3.8
224 7.3 25 50 6:1 063B-4 090 3.8
178 9.2 31 60 5:1 071A-6 090 3.8
167 9.8 32 70 4:1 080A-8 090 3.8
148 11.0 29 50 6:1 071A-6 090 3.8
112 14.6 30 50 6:1 080A-8 090 3.8
0.25 540 4.2 23 60 5:1 063B-2 090 3.8
450 5.0 27 70 3:1 071A-4 090 3.8
337 6.7 27 70 4:1 071A-4 090 3.8
296 7.7 31 70 3:1 071B-6 090 3.8
270 8.4 27 60 5:1 071A-4 090 3.8
225 10.1 25 50 6:1 071A-4 090 3.8
178 12.7 31 60 5:1 071B-6 090 3.8
148 15.3 29 50 6:1 071B-6 090 3.8
134 16.9 32 60 5:1 080B-8 090 3.8
112 20.3 30 50 6:1 080B-8 090 3.8
0.37 900 3.7 29 40 1.5:1 071B-4 090 3.8
675 5.0 27 30 2:1 071B-4 090 3.8
600 5.6 32 40 1.5:1 080A-6 090 3.8
560 6.0 23 60 5:1 071A-2 090 3.8
450 7.5 27 70 3:1 071B-4 090 3.8
337 10.0 27 70 4:1 071B-4 090 3.8
270 12.4 27 60 5:1 071B-4 090 3.8
225 14.9 25 50 6:1 071B-4 090 3.8
180 18.7 31 60 5:1 080A-6 090 3.8
150 22.4 29 50 6:1 080A-6 090 3.8
0.55 936 5.3 23 70 3:1 071B-2 090 3.8
906 5.5 29 40 1.5:1 080A-4 090 3.8
702 7.1 23 70 4:1 071B-2 090 3.8
680 7.3 27 30 2:1 080A-4 090 3.8
600 8.3 32 40 1.5:1 080B-6 090 3.8
562 8.9 23 60 5:1 071B-2 090 3.8
453 11.0 27 70 3:1 080A-4 090 3.8
340 14.7 27 70 4:1 080A-4 090 3.8
300 16.6 31 70 3:1 080B-6 090 3.8
227 22.0 25 50 6:1 080A-4 090 3.8
180 27.7 31 60 5:1 080B-6 090 3.8
0.75 1880 3.6 25 40 1.5:1 080A-2 090 3.8
1410 4.8 23 30 2:1 080A-2 090 3.8
1360 5.0 32 105 1:1 080B-4 090 3.8
940 7.2 23 70 3:1 080A-2 090 3.8
906 7.5 29 40 1.5:1 080B-4 090 3.8
705 9.7 23 70 4:1 080A-2 090 3.8
680 10.0 27 30 2:1 080B-4 090 3.8
564 12.1 27 60 5:1 080A-2 090 3.8
453 15.0 27 70 3:1 080B-4 090 3.8
340 20.0 27 70 4:1 080B-4 090 3.8
1.1 2820 3.5 27 105 1:1 080B-2 090 3.8
1880 5.3 25 40 1.5:1 080B-2 090 3.8
1410 7.1 23 30 2:1 080B-2 090 3.8
940 10.6 23 70 3:1 080B-2 090 3.8
705 14.2 23 70 4:1 080B-2 090 3.8